Free Press Release Center Logo
   
  Home | About Us | Sample Press Release
  Press Release Articles | Press Releases and SEO | Press Release Book  
 

Environmental Hygienists Release New Set of Steps for Toxic Mold Removal

Environmental Hygienists advocate ten mold remediation steps as the sure way to achieve a perfect mold removal outcome.

PDF  View as PDF  Print View   

May 3, 2013 (FPRC) --The Environmental Hygienists Association has released a new set of recommendations that property owners, managers, and tenants should take when battling with toxic mold removal.

1. Mold Inspection and Testing. Do thorough and complete mold inspection and testing to find all areas of both visible and mold growth hidden inside ceilings, walls, floors, heating/cooling equipment and ducts, crawl spaces, basements, and attics. Use a moisture meter, hygrometer humidity meter, and fiber optics inspection to help find hard-to-find mold infestation.

After the completion of all mold removal steps, use do it yourself or professional clearance mold testing of the air of remediated rooms, the outward air flow from heating, ventilating, and air conditioning (HVAC) duct registers, and horizontal and vertical surfaces inside the mold work area. For independent mold clearance testing, visit www.moldexpertconsultants.com.

2. Proper Containment. Seal off the room or area to be mold remediated with 6 mil thick floor-to-ceiling, wall-to-wall, clear plastic sheeting so that mold spores released during mold removal do not travel to and mold cross-contaminate other areas.

3. Proper Worker Protection. Mold removal workers should wear a 3M or comparable breathing respirator mask with organic vapor filters rated P100, available for about $40 from a large hardware or home improvement store, plus eye goggles with no holes ('chem splash' type), disposable vinyl gloves, and Tyvek or comparable protective body suits with built-in parka hood and booties.

4. Ozone Treatment. The first mold kill step should be to operate a high output ozone generator for at least six to eight hours inside the building’s heating/cooling equipment and ducts and inside the rooms or areas being mold remediated. The best value, high output ozone generator is the Bio3Blaster, available at www.ozonegeneratorkillsmold.com. There can be no people, pets, or live plants inside the area being ozone treated.

5. Mold Enzyme Treatment. Spray a wet coating of mold-dissolving enzymes on all visible moldy surfaces and adjacent surfaces to help separate mold growth from the building materials being eaten by the mold. MoldZyme® is available at www.molddiy.com. Allow the MoldZyme® to soak into the moldy building materials for 30 minutes before removing the mold growth (Step Six below).

6. HEPA Air Scrubbing and Vacuuming. After the completion of the ozone and mold enzyme treatments, run one or more HEPA industrial-sized air scrubbers inside the contained mold work area to establish negative air pressure therein to collect airborne mold sporesS, with the HEPA exhaust air duct going directly to the outdoors. Use one or more HEPA vacuums to vacuum walls, floors, carpeting, and furnishing surfaces three ways---horizontally, vertically, and diagonally.

7. Physical Mold Removal. While operating a HEPA air scrubber inside the mold work area, remove all visible mold growth by removing and discarding materials such as moldy drywall, curtains, and carpeting, and by cleaning wood timbers to visibly mold-free with the use of a power grinder with wire brush attachment, power sander, power planer, and/or hand held wire brushes and sanding blocks.

8. Safe Disposal of Moldy Materials. While inside the contained mold work area, place all removed moldy materials into 6 mil thick garbage disposal bags. Then, put each full bag inside a second 6 mil thick bag (known as 'double bagging'). Then, wipe off the outside of the outer bag with a cloth lightly damp with hydrogen peroxide or borax laundry detergent dissolved into water to remove any landed or deposited mold spores. Then remove the bags to the outdoors through windows or doors without taking the bags through building areas that are outside of the contained work area.

9. Encapsulation of Wood Timbers. After completion of the above steps, paint all exposed and remediated wood timber surfaces with white, glossy latex enamel paint into which one half pound of the EPA-registered fungicide Tim-Bor has been thoroughly mixed. Tim-Bor is a long-term preservative of wood against both mold and wood-destroying insects such as termites. The glossy latex paint coating will also help to protect the wood against water penetration in the event of a future plumbing leak, roof leak, or other water intrusion. Read about Tim-Bor at www.timborprofessional.com.

10. Clean and Disinfect HVAC Ducts. If there has been a mold problem inside a building, its heating, ventilating, and air conditioning (HVAC) ducts are likely to be contaminated with elevated levels of airborne mold spores and mold growth. Clean and disinfect HVAC ducts with these procedures: (a) hire an experienced air duct cleaning company to do thorough HVAC duct cleaning; (b) after duct cleaning, do a second ozone treatment with at least four to eight hours of high output ozone treatment into the return air duct to get mold-killing ozone everywhere in the HVAC system and throughout the entire building; and (c) after ozone treatment, use a fogging machine to fog thoroughly the HVAC ducts with Sporicidin Disinfectant Solution, one of the few fungicides approved by the U.S. Environmental Protection Agency for use inside air ducts.

For more information on how to do perfect mold removal, email mold experts Phillip and Divine Fry phil@moldnspector.com or phone Mr. Fry 480-310-7970 or 480-217-7173, or visit their websites www.moldinspector.com and www.certifiedmoldinspectors.com.

(30)




Send an email to Phillip Fry of Environmental Hygienists
480-217-7173

Recent Press Releases By The Same User

Mold Expert Phillip Fry Launches Mold Victim Rights Association To Help Individuals Sickened By Mold (Thu 16th May 13)

Mold Experts Recommend Frequent Cleaning Inside Air Conditioners and Ducts to Prevent Toxic Mold Infestations (Sun 28th Apr 13)

Mold Experts Recommend Regular Mold Testing of Office and Workplace Air Conditioning in Arizona, California, and Nevada. (Sun 28th Apr 13)

Mold Inspectors Recommend Mold Inspection Prior To Purchase of Homes and Buildings in Asia (Thu 11th Apr 13)

Taylor Moldmen Now Offer Mold Inspection, Testing, and Removal for Properties in Cebu and Visayas, Philippines (Thu 28th Mar 13)



Press releases by industry
Advertising
Aerospace and Defense
Architecture
Arts and Entertainment
Audio and Video
Automotive
Baseball
Basketball
Beauty
Beverages
Business
Chemicals
Christianity
Communication
Computers
Consumer
Crops
eCommerce
Economy
Education
Employment
Energy
Environment
Events and Trade Shows
Fashion
Finance
Food
Football
Forestry
Golf
Government
Hardware
Healthcare
Holidays
Human Resources
Immigration Services
Information Technology
Insurance
Internet
Investment Services
Legal
Leisure
Lifestyle
Linux and Open Source
Maritime
Media
Non-Profit
Photography
Plumbing and Heating
Politics
Public Relations
Railroads
Real Estate
Religion and Faith
Restaurants
Retail
Science
Society
Software
Sports
Technology
Television
Toys
Trade
Transportation
Travel and Tourism
Trucking
Volunteer
Waste Management
Water

[ Vist our sister sites: Linux news | Bible Study Tool ]

Site design and layout copyright 2005-2015 Free Press Release Center